ADLINK Technology cPCI-6860A Series Manual de usuario descargar pdf (Pagina 22)

14 Getting Started

2.4 Drive Bay Access

To install the required hardware in the two 5.25” drive bays, follow

the procedure below:

1. Remove the 16 screws fastening the chassis lid and lift it

off of the cPCIS-3320.

2. Remove the three screws fastening the drive bay

bracket to the internal chassis structure as shown in the

figure below. Remove the bracket from the chassis, undo

the four screws attaching the blanking cover to the drive

bay bracket, and remove the blanking cover.

Figure 2-5: 5.25” drive bay access.

3. Install the necessary hardware into the drive bay

bracket, replace the bracket into the chassis, and fasten

the screws attaching it to the internal chassis structure.

4. Make the necessary cable connections and replace the

chassis lid.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 75 76

9U Dual-System 1
CompactPCI Platform 1
User’s Manual 1
Getting Service from ADLINK 3
Table of Contents 5
List of Figures 7
1 Introduction 9
1.2 Specifications 10
1.3 Mechanical Layout 11
4Introduction 12
1.4 cPCIS-3320 Configurations 13
1.5 System Architecture 13
6Introduction 14
Introduction 7 15
1.6 Power Distribution 16
2 Getting Started 17
10 Getting Started 18
Getting Started 11 19
12 Getting Started 20
Getting Started 13 21
2.4 Drive Bay Access 22
2.5 Powering Up the System 23
2.6 System Alarm Board 24
3 Backplane 25
3.2 Mechanical Drawing 26
Backplane 19 27
3.3 Connector Pin Assignments 28
System Slots [8-P2], [14-P2] 29
System Slots [8-P3], [14-P3] 30
System Slots [8-P4], [14-P4] 31
System Slots [8-P5], [14-P5] 32
Peripheral Slots 33
26 Backplane 34
Pin Z A B C D E F 34
Backplane 27 35
28 Backplane 36
Pin Z A B C D E F 36
Backplane 29 37
CMM Slots 38
CMM Slots [S55] 39
Other Connectors 40
AC-Inlet Connector [CN8] 41
Power LED Connector [J5] 42
DEG# Connector [J8] 42
INH# Connector [J9] 43
FAL# Connector [J10] 43
3.4 Jumper Settings 44
4 Cooling System 47
Intake Fans 48
Exhaust Fan 49
42 Cooling System 50
Cooling System 43 51
5 Power Supply Unit 53
5.3 Input Characteristics 54
5.4 Output Characteristics 55
5.5 Pin Assignments 56
6 Chassis Management Module 57
CMM Mechanical Diagrams 58
Chassis Management Module 51 59
Features 60
Specifications 61
6.2 CMM Setup 62
Chassis Management Module 55 63
56 Chassis Management Module 64
Chassis Management Module 57 65
58 Chassis Management Module 66
6.3 CMM Firmware Update 68
Chassis Management Module 61 69
62 Chassis Management Module 70
Chassis Management Module 63 71
Important Safety Instructions 73
Warranty Policy 75
68 Warranty Policy 76

Comentarios a estos manuales

Sin comentarios

ADLINK Technology cPCI-6860A Series Manual de usuario Pagina 22

Comentarios a estos manuales

Relacionado con productos y manuales para Los componentes del chasis ADLINK Technology cPCI-6860A Series